Owner’s Manuals. Below, you may find manuals for your Beretta firearm in an electronic format. You may also order a hard copy if desired. Owner’s Manuals. Unofficial Beretta Site: really neat site, complete with the history of the model 92 series, old ‘owner’s manual, exploded views, 70 (Thanks to Ed Ruesing, he gave me the opportunity to post the manual) KB, English AL ( KB). The illustrations and instructions in this article are based on the Beretta Urika , but they are also valid for the other versions of the
|Published (Last):||18 September 2013|
|PDF File Size:||13.40 Mb|
|ePub File Size:||15.70 Mb|
|Price:||Free* [*Free Regsitration Required]|
If the ports get clogged, the gun will not cycle properly. Be careful not to let the plunger and spring fly out and get lost although the plunger often hangs up and has to be pried out if the safety is not going to be put back in.
If they did, please let me know what the real diiference is between the two guns. Yes, I said throw it away.
Carefully dry the choke housing using a soft patch. The cap must be heated to release the thread locker. The safety can be engaged only when the hammer is cocked. O pen and empty the chamber of your firearm before climbing or descending a tree or before climbing a fence or jumping over a ditch or obstruction.
The chance that gas, gunpowder or metal fragments will blow back and injure a shooter who is firing a gun is rare, but the injury that can be sustained in such cir- cumstances is severe, including the possible loss of eyesight. All ‘s sold in the US as far as I know come with a plug installed to limit shell capacity to 1 in the chamber and 2 in the magazine, with a longer plug in the box to limit capacity to 1 and 1.
Should this occur, the breech bolt would be kept OPEN by the cut-off lever. The large opening of the trigger guard allows the use of gloves.
The spring will probably be dirty and greasy. Then put the nut in the socket and turn the gun partly over on its side so you can get the socket inside without the nut falling out. Cleaning the gas ports: Don’t ask amnual how I know that, just take my word for it. In some areas, shooting is allowed only with shotguns having a capacity of no more than two rounds.
From this point with a new gun, it will help to get someone to hold the gun ufika while you pull the trigger group out.
Cock the gun and leave the bolt open. It will hold the barrel vertical while I screw my nuts off. Beretta apparently is afraid you are going to tighten the nuts so tight you damage something. You could just stop there and clean what you can see: If not, depress it completely. Fortunately, that can be done without disassembling the nut.
AL 391 Urika / Teknys Instruction Manual
Long Shot, I don’t have the link, but somebody posted a link to urjka picture off the Beretta web site that shows the long part of the valve shaft on the side next to the gas ports. Be certain that each round you use is in the proper caliber or gauge and type for the particular firearm. The safety button is held in place by a plunger and spring on the right side. Make sure thatthe safety is fully engaged. Magnum cartridges and particularly Super Magnum 3″ shotshells produce a high amount of combustion manuao.
I think my friend cleans his shaft every time he shoots, anyway. Never spray or apply oil to the shotshells. For best results with steel shot, Beretta recommends a modified choke.
Different stock drop and cast dimensions can be ob- tained using the extra set of spacers supplied. However, I did find a way to detect the twist. The Company, therefore, reserves the right to make, at any moment and without notice, any changes it thinks necessary to improve its models or to meet any requirements of manufacturing or commercial nature. Putting the trigger group back in is just the reverse – remember to press the bolt release button while you put it in.
Driving the pin out and putting it back in will be easier mannual you press in on the guide to take spring pressure off the pin.
For instructions on how to reinstall the carrier, see section F below in “Reassembly of the trigger group”. It goes in and out a lot easier, and it holds everything in just fine. No matter, you can clean it pretty well with those parts still in.
Go to Sears and get a small sized Robo Vise. The old spring will be shorter than the new one – sometimes there is a bigger manuao than shown in the illustration. Feeding from magazine is blocked.
The image below illustrates the technique: Be careful where you point the firearm, even though it might not be loaded, i Keeping the breech bolt retracted approximately 2 cm 1 inchto allow a visual check of the cartridge chamber to ensure it is empty, depress the trigger to lower the hammer.
If the trigger group is in, the hammer has to be cocked or the connecting rod won’t come out or go back in. How often they need cleaning depends on how clean-burning your ammo is. The ring looks like stainless. The plastic bushing is not used when the barrel is on, but it is needed to keep the forend nut from jamming when the barrel is off. The gas ports can then bdretta cleaned by sticking any suitable probe through the hole in the manaul of the gas cylinder, going all the way through the cylinder and into the ports in the barrel.
Use the two hook wrenches together as berrtta to break uriika counter nut loose. A great article on the