BRYSTON 4B SST MANUAL PDF

BRYSTON OWNER’S MANUAL Instructions For Bryston SST Series Amplifiers Models 3B SST and 4B SST 3B SST and 4B SST Series Amplifiers Table of. Audio manuals and audio service pdf instructions. Find the user manual you need for Bryston 4B SST Stereo Amplifier User Manual. Page 1. Page 2. Page 3. User guide • Read online or download PDF • Bryston 4BSST User Manual • Bryston Receivers and Amplifiers.

Author: Samull JoJotilar
Country: Azerbaijan
Language: English (Spanish)
Genre: Technology
Published (Last): 25 February 2009
Pages: 462
PDF File Size: 3.94 Mb
ePub File Size: 6.91 Mb
ISBN: 172-7-18230-346-7
Downloads: 97970
Price: Free* [*Free Regsitration Required]
Uploader: Shaktizahn

This is the home theatre setting for balanced operation Or use this setting with any systems where the volume control rotation is limited to the bottom half of the control or less.

In the event of dst defect or malfunction, Bryston will remedy the problem by repair or replacement, as we deem necessary, to restore the product to full performance. Master circuit – breaker.

The 2v setting provides an amplifier gain – 23 dB. Check that the voltage rating on the label conforms with your locality. The circuit feeding the 4B SST should be sufficient so as not to cause the circuit breaker to trip 15 amp min. Wiring the SST amplifier also see rear panel description Speaker wires should be as short as practical.

For this reason do not install anything directly above it. In general never use longer cables than necessary, never coil excess cable length, and keep signal wires away from AC power or speaker cables. Also see installation section on ventilation.

  AMANTE Y FELINO DE KELLY DREAMS PDF

On the rear panel is provided a high current plug for the power cord receptacle. Heat Dissipation 8 ohms – Bridged W 8 ohms Max.

Any SST channels thermally shutting down during operation indicates insufficient air flow, and a remedy must be found for cooling the amplifier. Clipping flashing red Clipping occurs when the channel output level no longer can follow the level increase at the input Overdriven input condition.

Each channel selects a balanced or single ended input. The 1v setting provides the most amplifier gain – 29 dB.

Bryston 4BSST User Manual

Banana plugs offer a quick disconnect option. Each SST channel gives the user the option of switching between either balanced input or single ended input. Push again and the amplifier will power-down. Ship the amplifier only in the original packing material, as the unit is not insurable by carriers otherwise. Lugs should be gold plated. When the power supplies have stabilized the channel will come manuall of mute and the LED will change to green normal operation.

Use paired wire of 22 to 18 gage sufficient in length between the source device and the SST amplifier. Never lift the safety ground to the amplifier nor remove the ground pin from the plug. Never operate the amplifier in a vertical position. Combinations may be used when bi-wiring. Stripped bare wire up to 3 gage can be inserted through the hole in the binding post and held in place by tightening the wst knob. Should the breaker trip, lower or remove the amplifier input signals.

  J 5804 TRANSISTOR PDF

Note that copper wire is malleable and may require further tightening after the initial installation. Bridge mode is for mono operation. Warranty coverage is automatic and commences with the original date of manufacture which is kept on file at Bryston.

Different input configurations result in slightly different noise readings. When the channel has cooled to a safe operating condition the channel will return to normal operation. It’s a community-based project which helps to repair anything.

Bryston 4B SST User’s Manual |

Do not install directly above other heat generating equipment. The amplifier will now power-up only when the control voltage is present on. This includes parts, labour and return shipping to the first owner and all subsequent owners. This will ensure ,anual amplifier is protected in future transport. See figure 2 below. All SST amplifiers are convection cooled.

Bryston 4BSST User Manual | 8 pages | Also for: 3BSST

Installation see brsyton mounting section if applicable Ventilation. The control current is determined by the source equipment. The 1v setting is used when the source is single-ended, or from a transformer coupled balanced source.

work_outlinePosted in Art