The CF Development Kit is intended as a development platform for the Refer to the CF93x-CF92x data sheet for the differences between. Explore the latest datasheets, compare past datasheet revisions, and confirm part lifecycle. Buy SILICON LABS CFGQ online at Newark element Buy your Technical Datasheet: CFGQ Datasheet. See all Technical Docs. X. X.
|Published (Last):||12 December 2008|
|PDF File Size:||10.47 Mb|
|ePub File Size:||2.40 Mb|
|Price:||Free* [*Free Regsitration Required]|
In dual-cell battery mode, this pin must be connected directly to ground. The header J6 provides access to the ground plane for easy clipping of oscilloscope probes. Configuration Wizard 2 Utility The Configuration Wizard utility helps accelerate development by automatically generating initialization source code to configure and enable the on-chip dataseet needed by most design projects Prev Next CF D.
Silicon Laboratories, Inc. C8051F930
In-system Flash memory datasheet integrated into the driver allows for rapid updating of target code. Factory Defaults The CF target dxtasheet comes from the factory with pre-installed shorting blocks on many headers. In reality, this issue had me stumped before I resorted to utilizing an SPI bus analyzer. The alarm and the lights will stay energized until datasjeet microcontroller is reset.
Continue adding files until all project files have been added. The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice.
Register 0x32 sets the acceleration threshold set to mg for when the Int1 signal is driven; the mg threshold setting is what makes the motion detector so sensitive to slight accelerations. CD content includes the following:. CF93x 92x Errata Rev0.
Figure 9 shows the positions of the factory default shorting blocks. Right-click on the group name and choose Add file to group.
CFGM 8-bit Microcontroller – Silicon Labs
This will allow the low power oscillator to be disabled when it is not being used as the system clock. The Crossbar cannot route signals to this pin and it cannot be configured as an analog input. Information windows will pop up from the taskbar to show the installation progress. How to Design a Super Simple Sensor System for Industrial Monitoring Applications This article describes an Ethernet-connected subsystem of a larger modular sensor system designed for industrial or smart home sensing and A In AD1 P1.
The CF Development Kit should become visible as an option—click on this option see Figure 8 below. This project uses a C microcontroller development kit, an accelerometer evaluation board, and Simplicity Studio IDE—all from Silicon Labs—to datashedt quickly and easily build a motion-detecting alarm system. In single-cell battery mode, this pin is typically not connected to ground.
Select the profile that most closely matches the target application or choose the “Custom Profile”. Trademark Information Silicon Laboratories Inc. In addition, power supply and ground pins are included.
Build Your Own Motion Detection System Using an Accelerometer
Give this project a try for yourself! V are selected when SW4 is configured to two-cell mode. Additional outputs include estimated battery capacity, average current, self-discharge current, and the ability to export graph data to a comma delimited text c8051r930 for plotting in an external graphing application.
Alternatively, a shorting block can be placed on J17 to ensure that the multimeter does not limit current during startup. Silicon Laboratories reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give dattasheet as to the accuracy or completeness of the included information.
See Figure 9 below. This pin is the excitation driver for an external crystal or resonator. Serial Interface Header J12 Description 7. Keil Assembler and Linker The Keil demonstration toolset assembler and linker place no restrictions on code size.
LED flood light qty 2. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific device, and “Typical” parameters provided can and do vary in different applications.
This kit comes with the CF microcontroller installed—see Figure 1 below.
BT4 Battery Holder for 1. This pin can only be used as GPIO. The four text entry boxes on the left hand side of the form allow the user to specify the amount of time the system spends in each power mode