Model, DSO Oscilloscope Mode. Vertical System. Analog Channels, 4. Bandwidth, 60MHz(-3dB). Rise Time, ns. Input Impedance, Resistance: 1MΩ; . Hello to everyone. I bought an Hantek DSO KIT IV from an online reseller. I need to say I was impressed with the packaging and. DIGITAL OSCILLOSCOPE. USER’SMANUAL . Connect the B-Type Plug of USB cable to DSO USB’S USB port. 3.
|Published (Last):||14 May 2017|
|PDF File Size:||8.20 Mb|
|ePub File Size:||19.70 Mb|
|Price:||Free* [*Free Regsitration Required]|
On my c the ht25 waveform looks like crap compared to the primary waveform. Product Registration After-sales service Questions. In general, I find you can’t practically use more than two of the channels. I used the included leads.
I hooked both power and ground clips to my battery negative on all the channels I used and ran the calibration right before making this gantek. I own two of their amp clamps one works fine the other arrived broken and I had to spend two hours fixing it to get it to work. Please Log in or Create an account to join the conversation. I read somewhere the Hantek software behaved better if you start capture by clicking Auto button, so I did.
This board is factory installed on oscilloscopes as an optional interface and should require no futher connections to be made to it. Apply to logic analyzer. Multimeter Probe HT pair Meter probe with standard plug 4mmsuitable for universal. Automotive electronics continue to evolve and becopme more complex.
Be the first to hantwk this product. Auto Power Adapter HT Basically, some cars have pretty well insulated plug wires, which can degrade the quality of the signal one gets.
Hantek PC Based Oscilloscope Arbitrary Waveform Generator Spectrum Analysis | eBay
Auto Test Leads HT30A pc It’s a special line for assisting auto measurement instruments to test various types of signals. I’ve been playing with my hantek c and the ht25 and cc65 and I’ll probably hantem about my experiences. Multimeter Probe HT19 pair The multimeter probes offer a quick and easy solution, where a permanent connection is not required. I don’t have enough experience with DSO’s to make qualified judgments but my initial impression is I was hoping for more.
I have a DSO An oscillocsope may be used equally well for making measurements in cars, lorries or motorcycles. The lead with 4 kinds of joint size: The HT25 was used for the secondary captures and the CC is clamped on the ground wire at the distributer.
Optional car power adapter and cord for oscilloscope. Just because spell check says it’s OK, doesn’t mean it is. With each Hantek Autoscope profiset you will get the following technical support: The key features for automotive diagnostics The key feature of the Autoscope is an extensive database of preset measurements for various sensors and actuators.
I’m also just starting out and I actually ordered a be which will probably be here in about two weeks. The longer it was used, the more it would bog down the computer. The multimeter probes offer a quick and easy solution, where a permanent connection is not required.
Test lead of a male BNC connector to 2 4mm connectors. Designed to aid diagnostics on secondary ignition circuits by allowing an HT measurement to be made when there are no, or limited access, to any spark plug leads. Simple accessory that allow you to take accurate secondary ignition measurements on COP ignition systems. Index Recent Topics Search. Maybe I’ll post some video links.
HANTEK DSO3064 Kit VII 60 MHz Automotive Oscilloscope System
I haven’t used it yet, but I just ordered one myself and it will be here in a few weeks. MacFadyen Replied by Andy. Our Partner Manufacturer Hantek.
Habtek you’re on a really tight budget, it would be better to get the two channelas it’s higher bandwidth and there is also decent third party software for it, openHantek or sigrock.
Please have a look at my hookup. Power your oscilloscopes and other electronic devices through your vehicle’s DC outlet with this power adapter.
You need to run the calibration after the scope has been turned on a while and warmed up. On my scope, it says to hook up all the channels being calibrated to a ground.
If buyimg again I would just buy generic amp clamps.