HEATHKIT HM-2102 BULLETIN PDF

Fig 1: Heathkit HM HF RF Power Meter. The HM Meter for VHF is SImilar. Part #. Began Ended Frequency MHz. Power Watts. Notes. HM line of Heathkit SWR bridges and, later, power meters. The Heathkit HM SWR Bridge Meter: HM for VHF. . issue of RF, the newsletter of the. The Relay Modification Kit [PN ] is available from Heath Parts . March 2, HM Bulletin No: VHF Watt Meter HM

Author: Shakajora Brall
Country: Mauritius
Language: English (Spanish)
Genre: Love
Published (Last): 7 September 2014
Pages: 365
PDF File Size: 8.35 Mb
ePub File Size: 20.16 Mb
ISBN: 869-4-57940-131-8
Downloads: 56044
Price: Free* [*Free Regsitration Required]
Uploader: Ditaur

Use additional packing material where there are protrusions control sticks, large knobs, etc. You can better understand the extent of this effect when you realize that a line with a 3 dB loss will show an SWR of 3: The blue and white label shows the model number and production series number of your kit. If the meter reads higher than 1. When the load is matched, the SWR will be low, approaching 1: Connect the 3″ prepared end of this cable to the cabinet components in the following steps.

Shipping cost cannot be calculated. Capacitors C3, Heathkot, C5, and C6 form a voltage divider circuit to balance the capacitive effects of the bifilar doubled windings in coil L1, which provides correct SWR readings. Pull the bracket down as far as it will go, as shown, before tightening the screws.

Full text of “Heathkit HM VHF Wattmeter (manual)”

I’m going to get a different working swr meter to check the accuracy of this Meter. Solder the leads to the foil and cut off the excess lead lengths. Nearby transmitter in operation.

  GERHART HAUPTMANN DER BIBERPELZ PDF

Therefore, scrape away the colored protective coating from the foil where the small spacer will contact it. Back to home page. Use only one of the two following procedures. Look up this Description in the “Parts List. Gently pull the cable from the remote chassis and place the length hn-2102 insulation and the strain relief on the cable 1” from the hole.

Heathkit HM RF POWER / SWR Meter For VHF Ham Radio | eBay

Disconnect the transmission line and place the remote chassis face down on your work surface. Twist the bare wire ends tightly and apply a small amount of solder to each end to hold the small strands together. Mount a coaxial connector on the outside of the remote chassis at A. You can download a manual at heathkig In the following steps, you will install the remote chassis in the cabinet.

Avoid eye injury when you clip off excess leads. Seal the carton with reinforced gummed tape, tie it with a strong cord, and mark it “Fragile” on at least two sides. Add to watch list. Resume making your offerif the page does not update immediately.

This will reduce the possibility of delay. Heathkit Electronic Center facilities are also available for vulletin or “walk-in” personal assistance.

Connect the black wire to the negative unmarked meter lug S Parts are also available at the Heathkit Electronic Centers listed in your catalog. Use this nut starter to hold and start and nuts heatbkit screws.

  4957A MANUAL PDF

Diode D1 or D2 reversed. SWR null not correct, No meter reading. SWR Sensitivity Less than 1 0 watts. Resistors R7 and R8 are voltage dividers for the two power ranges: See terms – opens in a new window or tab. Any international shipping and import charges are paid in part to Pitney Bowes Inc.

You bhlletin obtain parts directly from Heath Company by writing us or telephoning us at Push the switch in and note the meter reading. New 16 pF and 17 pF capacitors will be in the line in the future and this modification may be used until the new capacitors are available.

Heathkit Service Bulletins – HG/HL/HM/HN/HO (Complete)

A load must be connected to the output jack of the Meter. Cut 4″ from one end of the cable. Kits that have been modified, soldered with paste flux or acid core solder, cannot be accepted for repair. When the switch is set at the SWR setting, the Wattmeter measures the reflected power and indicates on the SWR scale the mismatch between the transmission line and the load antenna.