LM1391N DATASHEET PDF

LMN Texas Instruments Phase Locked Loops – PLL datasheet, inventory, & pricing. LMN Datasheet PDF, pdf, pinout, equivalent, replacement, schematic, manual, data, circuit, parts, datasheet. National Semiconductor LMN: available from 2 distributors. Explore Integrated Circuits (ICs) on Octopart: the fastest source for datasheets, pricing.

Author: Fenrizragore Faugore
Country: Haiti
Language: English (Spanish)
Genre: Environment
Published (Last): 4 June 2006
Pages: 293
PDF File Size: 13.4 Mb
ePub File Size: 10.90 Mb
ISBN: 583-5-65891-637-5
Downloads: 6191
Price: Free* [*Free Regsitration Required]
Uploader: Nataur

Also of concern is the possible mating of IC chips, solder-bump chips, or film-strip chips into the display assembly. A-l 1, Figure 2 DWG.

Therefore, techni- ques similar to those used for handling MOS devices should be employed. A- 1 1Single-chip construction and the power-tab TO style package provide improved cost ef- fectiveness and reliability over discrete compo- nent motor drive systems with excellent power dissipation capability, minimum size, ease of in- stallation, and heat sinking.

Capacitor C datasheey should be temperature stable NPO. These types are for general purpose applications such as motors, solenoids, relays, filaments, etc. With proper matching of parts and lots, consistent device performance can be obtained.

The bipolar outputs may be used as segment, dot matrixbar, datassheet digit drivers in vacuum fluorescent displays. Prospects for purchasing a display complete with all drive electronics, such as a flat panel a-c plasma matrix chips mounted via hybrid techniques on the rear of the glass envelopeare improving with time.

The Datasgeet N 0N voltage limit guarantees a minimum output source current per the specified conditions. For non-inductive loads, ,m1391n diode common bus can be used as a convenient lamp test. The mixer’s high input im- pedance matches popular The highest voltage parts suffix A-l are also used in gas-discharge display applications as anode digit drivers.

This makes the construction of a stable amplifier much easier. The high-voltage bipolar interface is designed for use in the anode portion of a display. EX Toko Part No. Type ULNA will work with a wide range of supply voltages, and is suitable for use in a-c powered table radios and in battery-powered 6 or 9 V portable radios. The output transistors are capable of sinking mA and will sustain at least 50 V lmm1391n the off state.

  CANON IPF810 PDF

LMN datasheet & applicatoin notes – Datasheet Archive

Per- formance specifications, truth tables and timing charts for these integrated circuits appear on previous pages. Testing Failure Mode Contamination Package-Related Process-Related Electrical Degradation The majority of early integrated circuit failures infant mortality or ionic con- tamination can be attributed to manufac- turing defects, package or assembly defects, or final test escapes. Voltage values shown in the test circuit waveforms are with, respect to network ground terminal.

With a typical display current of 3 to 5 mA, the gas discharge drivers are perfectly adequate.

Radio designs using Type ULN- A can be revised for greater power output or for stereo operation without reworking the printed wir- ing board layout by replacement of Type ULN- A with Type ULXA and addition of ap- propriate stereo decoders datasheeh audio power amplifiers. Outputs can be paralleled for higher current capability. Typical applications include driving peripheral loads such as incandescent lamps, light-emitting diodes, memories, heaters, and other non-inductive loads of up to mA both drivers in parallel.

Direction Control The direction of output rotation is determined by the logic level at pin Typical time between vatasheet activation and output on to off transition A common-cathode LED configuration is shown dataxheet Figure 7 for currents of up to 1. If AFC is not required, pin 1 1 should be grounded, or tied to pin 9 to double the available recovered audio.

As an example, if the tuner design requires 2. For strong on-channel signal levels, the wide-band R-F gain is determined by the strongest in-band signal. The availability of these devices is especially significant in view of the increasing use of microprocessor-based con- trols for servo and stepper motors. Both devices are capable of sinking 1. New functions are becoming available along with increased power handling capability, high voltages, etc. UCNA This integrated circuit functionally replaces a bit serial-in, parallel-out shift register, a bit data latch, and 10 high-voltage buffers including output pull-down resistors.

The l, N 0FF current limit guarantees against partial turn-on of the output. Sprague CMOS devices feature input static protection but are still susceptible to damage when ex- posed to extremely high static electrical charges.

  BEMISIA ARGENTIFOLII PDF

The earliest and a great many recent gas discharge interface schemes used discrete components, but that has been an increasingly cumbersome and expensive solution. Emitter follower Q 4 and Q 5 sources current to the pull-up bus connected to the various outputs as they are turned on during the display scan.

Datasheet (4)

It will only require one manufacturer willing to be a pioneer to further swing display technology into integrated systems. This communications I-F system meets the stability requirements of many automotive ap- plications, and also meets the low-power demands of portable radio design.

An added intent is the measure of protection furnished the MOS by the very high impedance of Rj. Type ULNA exhibits 35 dB suppression of the kHz pilot and 45 dB rejection of the regener- ated 38 -kHz subcarrier at demodulator output termi- nals.

Exact replacement in all applications is not guaranteed and the user should compare the specifications of the competitive and recommended Allegro replacement.

PDF第号导航-IC datasheet

A fully-balanced, four-stage differential I-F amplifier gives maximum gain with freedom from common mode signals. In addition, the Q48 divider cir- cuit is refined to reduce PNP beta dependence. These devices provide output currents suitable for display segments in a wide variety of display sizes and number of display digits.

The substrate must always be tied to the most negative point and must be at least 4.

The devices can be used in a wide variety of low- to high-voltage applications. Keep appropriate distance between the input pin 4 and the input network and the phase shift network pins 9, 10, and 12, and the phase shift inductor.

Two basic changes have occurred relatively recently: During this same period a-m integrated circuitry showed far less inspiration. The dwtasheet terminal 9 is referenced near, or connected directly to ground, and the V KK line is typically a – 90 to – datashwet.

work_outlinePosted in Video