MAGNETEK GPD 515 PDF

The Yaskawa / Magnetek GPD /G5 Sine-Coded Pulse Width Modulated AC Motor Drive generates an adjustable voltage/frequency three phase output for. TTThhhooommmpppsssooonnn CCCooo RRReeellleeeaaassseeeddd /// /// 2. Magnetek GPD AC Drive Start Up and Adjustment Guide. Magnetek G5 GPD | Drives | NEW IN STOCK | CALL or Click for Quote.

Author: Sajinn Meziran
Country: Croatia
Language: English (Spanish)
Genre: Business
Published (Last): 15 February 2009
Pages: 319
PDF File Size: 1.98 Mb
ePub File Size: 10.60 Mb
ISBN: 925-4-30188-429-5
Downloads: 28011
Price: Free* [*Free Regsitration Required]
Uploader: Doubei

GPD 515/G5 Drive Technical Manual

The output is then held at that frequency for the duration of the dwell time at stop b 6 – 0 4. CAUTION Applications that require decelerating large inertia loads in very short decel times may cause overshoots, and a possible runaway condition, causing equipment damage.

LCD Keypad can be used to copy parameter settings More information. If the fault can now be reset, the cause is most likely the motor or wiring to the motor. Some quick and general information on the fault indications and causes are listed in this article. When the Base Block command is removed, the drive will recover in a manner similar to that of Speed Search operation, except that it searches up from 0 Hz, and supersedes a Speed Search command.

This information is supplemental More information.

Speed Coincidence Detection Width Factory setting: Field Compensation At Start Factory setting: Use a voltmeter to verify that voltage is disconnected from incoming power terminals. Do not work alone. This experience, combined with backgrounds in engineering and education, has earned national recognition for our technical gpc programs. The illustrations, charts and examples given in.

  INDICACIONES ESOFAGOGRAMA PDF

Except for the most demanding of high starting torque applications, the factory settings of these parameters will be adequate. Fine tune as indicated in A or B above. Course content can be customized to the specific installation and application if requested.

Easy to configure – The More information.

GPDG5-Installation | Yaskawa MagneTek Troubleshooting by Yaskawa | MRO Electric

This function applies only to frequency references at terminal 13 or Intelligent See Note 2 0 1 2 3: Maximum Output Frequency Maximum Voltage. When OC or UV occurs during deceleration. Step A Display the frequency reference that was present when the fault occurred.

After that length of time the drive continues to decelerate until the output frequency is zero. Table and Figure show connections for the PG-X2 and some typical encoders. A Motor overload Protects the motor.

Learn More – opens in a new window or tab International shipping and import charges paid to Pitney Bowes Inc. One of two methods may be used to run the drive in torque control. Linda Linda – NS, Canada. Pressing this key will display the top level of the menu tree for returning to the Drive mode. Factory setting differs depending on drive capacity. Therefore, it will not stop in the same position every time the servo function is enabled.

  1999 BUICK CENTURY MANUAL PDF

During dynamic braking operations, ensure that the required deceleration characteristic is obtained. A gld d d 0. The User Program Access Level will only be available if one or more parameters are programmed into A 2 – 0 1 through A 2 – 3 2. Some faults can be cleared be unseating and reseating an option card to make sure there is a good connection.

Want it shipped today? Contact Base block operation is the same as described above, except that the Base Block contact must be open to be recognized. Setting must be 5 digits. There are 1 items available. An excessively short deceleration time will generate an overvoltage fault Pgd and the drive will stop.

Yaskawa Magnetek GPD Gpdc-b Spec 40p71f 2 HP Drive 3ph v | eBay

Frequency Reference Magnftek Detection Factory setting: Up to 50 parameters may have data stored as their new user-defined initialization value. Factory Connection to control terminal 12 1 Customer supplied. After power recovery, if the drive output current is larger than the set value of b 3 – 0 2speed search is started, using a decel rate per the setting of b 3 – 0 3.